RHINO RAMPS MAX HEAVY DUTY 7 TON GVW LOW CLEARANCE VEHICLE CAR VAN RAMPS (PAIR)
RHINORAMPSMAX - HEAVY DUTY 7 TON GVW PRO WORKSHOP LIFTING RAMPS 11912MIE
This set of RhinoRampsMAX perfect for doing work on vehicles at home or elsewhere (not for commercial use). The ramps allow for easy lifting of the front of a car or truck for greater clearance and easier access when changing oil or performing other tasks. It is made of durable plastic and has a 7200 kg, 16,000 lb GVW (Gross Vehicle Weight) capacity and a 17-degree incline for accommodating low-clearance vehicles. A nesting design makes these plastic ramps easy to store while skid-resistant feet keep them firmly in place
RATED CAPACITY OF 4,000 LBS (1,814 KG) EACH / 8,000 LBS (3,628 KG) PER PAIR / 16,000 LBS (7,257 KG) GVW (GROSS VEHICLE WEIGHT)
Skid-resistant feet
17-degree incline for low-clearance vehicles
Durable plastic design
Nesting design for easy storage
Vehicle ramps dimensions: 36"L x 13"W x 8.5"H
Improved tread pattern
WARNING
STUDY, UNDERSTAND AND FOLLOW ALL WARNINGS BEFORE USING RAMPS. FAILURE FOLLOW WARNINGS CAN RESULT IN DEATH, PERSONAL INJURY OR PROPERTY DAMAGE.
- Do not exceed rated capacity of 4,000 LBS (1,814 KG) each / 8,000 LBS (3,628 KG) per pair / 16,000 LBS (7,257 KG) GVW (Gross Vehicle Weight)
- Use only on a hard level surface capable of sustaining the load. Use on other than hard, level surfaces may result in property damage, injury or death.
- Centre load between sides of ramps. Place ramp inclines centered and tight against both left & right front or both left & right rear wheels. Ramps must be inline with the vehicle and wheels pointed straight forward.
- Use only as matched pair to support either front or back end of a vehicle.
- Inspect ramps before each use. Do not use if damaged or cracked. Rubber feet should be in place on each ramp and ramps should be cleaner from oil and dirt.
- Destroy and discard if worn or damaged.
- Another person standing clear of the vehicle should observe and guide the vehicle operator when ascending and descending the ramps.
- Ramps are not to be used to simultaneously support both ends or one side of a vehicle.
- Not intended for storage on the incline of the ramps. Do not use as a leveling device.
- Use on vehicles with a maximmum tyre width of 9.5 inches.
- Do not use other lifting equipment in conjuction with the ramps.
- Do not disconnect brakes, engine, transmission components, drive train, drive shaft, universal joints or wheels while the vehicle is on the ramps.
- Never accelerate or apply brakes suddenly. Proceed slowly and cautiously. Once the vehicle reaches the top of the ramps, apply brakes only to prevent over travel. Braking while ascending may cause ramps to slide or tip.
- Do not use ramps on slick surfaces.
- When tyres come to rest in cradle area of the ramps, place the vehicle in neutral. Release brakes. Vehicle should not move. Apply hand brake. Place vehicle in park (automatic) or reverse gear (manual). Chock wheeks on ground.
- Be sure that both tyres are properly positioned on the ramps support platform. Using caution in positioning your body clear of danger, shake vehicle sideways and endways to be sure that vehicle and ramps are stable.
- Check that ramps have not become damaged or bent during loading.
- Only attachments and/or adaptors supplied by the manufacturer shall be used .
- Each ramp shall be inspected immediately if it is believed to have been subjected to an abnormal load or shock.
- No alteration shall be made to these ramps.
- Make certain that the operator thoroughly understands the inherent dangers associated with the use and misuse of these ramps. If any doubt exists as to the safe and proper use of this product please remove until it is clear.
- These ramps shall be maintained in accordance with these warnings.